View MSK4852H_1284423.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIL-PRF-38534 CERTIFIED
M.S.KENNEDY CORP. FEATURES:
1200V/150A THREE PHASE BRIDGE PEM WITH BRAKE
4852
(315) 701-6751
4707 Dey Road Liverpool, N.Y. 13088
Full Three Phase Bridge Configuration with SCR/IGBT Brake 1200V Rated Voltage 150A Continuous Output Current Internal Zener Clamps on Gates Proprietary Encapsulation Provides Near Hermetic Performance MIL-PRF-38534 Screening Available (Modified) Light Weight Domed ALSIC Baseplate Robust Mechanical Design for Hi-Rel Applications Ultra-Low Inductance Internal Layout Withstands 96 Hours HAST and Thermal Cycling (-55C to +125C)
DESCRIPTION:
The MSK 4852 is one of a family of plastic encapsulated modules (PEM) developed specifically for use in military, aerospace and other severe environment applications. The Three Phase Bridge configuration along with the SCR/IGBT brake circuit and 1200 volt/150 amp rating make it ideal for use in high current motor drive and inverter applications. The Aluminum Silicon Carbide (AlSiC) baseplate offers superior flatness and light weight; far better than the copper or copper alloys found in most high power plastic modules. The high thermal conductivity materials used to construct the MSK 4852 allow high power outputs at elevated baseplate temperatures. Our proprietary coating, SEESTM - Severe Environment Encapsulation System - protects the internal circuitry of MSK PEM's from moisture and contamination, allowing them to pass the rugged environmental screening requirements of military and aerospace applications. MSK PEM's are also available with industry standard silicone gel coatings for a lower cost option.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
Motor Drives Inverters
1 PRELIMINARY Rev. 1/06
ABSOLUTE MAXIMUM RATING

8
ELECTRICAL SPECIFICATIONS
NOTES:
Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified. Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2 and sample tested to subgroup 3. Subgroups 4, 5 and 6 testing available upon request. Subgroup 1, 4 TA = +25C 2, 5 TA = +125C 3, 6 TA = -55C 6 All specifications apply to both the upper and lower sections of the half bridge. 7 VGE=15V unless otherwise specified. 8 Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. 1 2 3 4 5
2
PRELIMINARY
Rev. -

VCE VGE IOUT IOUTP VCASE
Collector to Emitter Voltage Gate to Emitter Voltage Current (Continuous) Current Pulsed (1mS) Case Isolation Voltage
1200V 20V 150A 300A 2500V
TST TJ TC
-55C to +125C Storage Temperature Range 150C Junction Temperature Case Operating Temperature Range -55C to +125C MSK 4852H/E -40C to +85C MSK 4852
1/06
TYPICAL PERFORMANCE CURVES
TBD
3
PRELIMINARY
Rev. -
1/06
SCREENING CHART
4
PRELIMINARY
Rev. -
1/06
MECHANICAL SPECIFICATIONS
WEIGHT = 442 GRAMS MAX.
ORDERING INFORMATION
MSK4852 H
SCREENING BLANK=INDUSTRIAL; E=EXTENDED RELIABILITY; H=MIL-PRF-38534 CLASS H (MODIFIED) GENERAL PART NUMBER
THE ABOVE EXAMPLE IS A MILITARY SCREENED MODULE.
M.S. Kennedy Corp.
4707 Dey Road Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 qualification status.
5
PRELIMINARY
Rev. -
1/06

▲Up To Search▲

Price & Availability of MSK4852H

	To Download MSK4852H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .